Cleveland-motion-controls ULTRA ISC CARTRIDGE TRANSDUCER REV AA Bedienungsanleitung

INSTRUCTION MANUAL (MAN-70430-0) FOR ULTRA ISC CARTRIDGE TRANSDUCER FOR USE WITH STATIONARY SHAFTS

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 2 1.2 Features Ultra ISC load cell features are:  Factory Calibrati

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 1.5 General Specifications Item Specification Comments Input Supply

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 4 1.8 Operating Conditions Condition Isolated Signal Conditioning Amp

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 1.11 Block Diagram of Ultra Series ISC Amplifier Module Figure 2 Block

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 6 2 PRODUCT COMPONENTS The Ultra Series ISC Cartridge Tension Transduc

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 2.1 M12 Mating Connector The M12 connector used on the Ultra Series ISC

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 8  In environments with severe electromagnetic noise, it may be neces

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL Table B lists the part numbers and descriptions for these available cord

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 10 analog signal from an internal op-amp (operational amplifier) buffer

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 3 PRODUCT APPLICATION The Ultra Series Cartridge Cell Transducer utiliz

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-704300 REV AA REVISION HISTORY Rev ECO# Author Date Description of Change AA -- WGW

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 12 In the following schematic using the resistance values shown, the eq

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 3.3 Summing By “Series Stacking” The final interface approach to be dis

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 14 4 INSTALLATION 4.1 Receiving and Unpacking After receiving the Ultr

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 4.2.2 MOUNTING CONFIGURATIONS Ultra Series Cartridge Transducers can be

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 16 4.2.3 MOUNTING HARDWARE AND FASTENER TORQUE RECOMMENDATIONS Table E

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL (Flange) Flange Bolt M12-1.75 18 Mechanisms used for industrial auto

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 18 4.2.4 MOUNTING DIMENSIONS E (MAX)VR (MAX)C I B (MAX)DFHCVFWW/2GTUQQ/

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL W 1.75 1.88 Y 1/2 1/2 Z 1.50 1.70 W 44.5 47.6 Y M-12 M12 Z 38.1 4

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 20 4.4 Mounting the Transducer The mounting surfaces for the transduce

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 4.5 Mounting the Sensing Roll The following steps take into considerati

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL WARRANTY AND LIMITATION OF LIABILITY All equipment is sold subject to t

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 22 Tighten the shaft coupling cap. Be sure that the size of the gaps on

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 4.9 Power-up and Testing 4.9.1 BEFORE APPLYING POWER Before applying pow

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 24 4.10 Adjustment Tools (Only If Not Using Numerical Correction) Usin

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 4.12 Proper Practices for Applying Calibration Forces Seldom is a trans

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 26 4.13 Applying Force to Transducers The application of an accurate ca

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL  When two transducers support a roll, calibrate with the cord in the e

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 28 4.16 EMC Connections and Installation Compliance with the specified

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 4.17 Cable Glands Several manufacturers provide cable glands that can b

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 30 5 TROUBLESHOOTING Safety should not be an afterthought. Before ins

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 5.1 Transducer Bench Testing Because the strain gage signal conditioning

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA IV BLANK

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA 6 MANUFACTURERS DECLARATION OF CONFORMITY 32

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL TABLE OF CONTENTS 1 1 PRODUCT OVERVIEW ...

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA VI 4.13 Applying Force to Transducers ...

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL WARRANTY Cleveland Motion Controls warrants the goods against defects

ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL MAN-70430-0 REV AA BLANK VIII

MAN-70430-0 REV AA ULTRA SERIES STATIONARY SHAFT TRANSDUCER TECHNICAL MANUAL 1 PRODUCT OVERVIEW 1.1 General Description The Ultra Series Integrated S